public/Test-SnmpConnection.ps1
|
<#
.SYNOPSIS Tests connectivity and authentication to an SNMP-enabled device. .DESCRIPTION Verifies that an SNMP-enabled device is reachable and responds to SNMP requests using the specified credentials. The cmdlet performs a GET request against the specified OID and returns information about the success or failure of the test. Supports -Quiet for simple success/failure output. .PARAMETER ComputerName Hostname or IP address of the target device. Accepts pipeline input directly and by property name. .PARAMETER Port UDP port used for SNMP communication. The default value is 161. .PARAMETER Oid OID used to verify connectivity. The default value is sysDescr.0 (1.3.6.1.2.1.1.1.0). .PARAMETER Timeout Maximum time, in milliseconds, to wait for a response to each individual SNMP request. The default value is 5000 milliseconds. 0 and -1 indicate an infinite timeout. .PARAMETER Version SNMP version to use. Default version is V2C. supported values: - V1 - V2C - V3 .PARAMETER Community SNMP community string. Default value is 'public'. Only available when using SNMP v1 or SNMP v2c. .PARAMETER Username SNMPv3 user name. Only available when using SNMP v3. .PARAMETER AuthenticationProtocol SNMPv3 authentication protocol. Supported values: - MD5 - SHA1 - SHA256 - SHA384 - SHA512 Only available when using SNMP v3. .PARAMETER AuthenticationPassword SNMPv3 authentication password. Only available when using SNMP v3. .PARAMETER PrivacyProtocol SNMPv3 privacy protocol. Supported values: - DES - 3DES - AES - AES192 - AES256 Only available when using SNMP v3. .PARAMETER PrivacyPassword SNMPv3 privacy password. Only available when using SNMP v3. .EXAMPLE Test-SnmpConnection ` -ComputerName printer01 Tests connectivity to the SNMP-enabled device at printer01 using the default SNMP version (V2C) and community string (public). .EXAMPLE Test-SnmpConnection ` -ComputerName printer01 ` -Quiet Returns True when the SNMP agent responds successfully, otherwise returns False. This is useful for scripting and conditional logic. .EXAMPLE Test-SnmpConnection ` -ComputerName switch01 ` -Version V1 Tests connectivity to the SNMP-enabled device at switch01 using SNMP version 1 and the default community string (public). .EXAMPLE Test-SnmpConnection ` -ComputerName switch01 ` -Version V3 ` -Username admin ` -AuthenticationProtocol SHA512 ` -AuthenticationPassword $AuthenticationPassword ` -PrivacyProtocol AES ` -PrivacyPassword $PrivacyPassword Tests connectivity to the SNMP-enabled device at switch01 using SNMP version 3 with the specified username, authentication protocol, authentication password, privacy protocol, and privacy password. .EXAMPLE 'printer01','printer02','switch01' | Test-SnmpConnection Tests SNMP connectivity to multiple devices. .OUTPUTS ConnectionTest Returns a connection test result containing the target device, SNMP version, success state, response time and any error message. .NOTES This cmdlet performs an SNMP GET request against the specified OID to verify connectivity and credentials. A successful result indicates: - The target device is reachable. - The SNMP service is responding. - The supplied credentials are valid. - The requested OID is accessible. When -Quiet is specified, the cmdlet returns only True or False. #> function Test-SnmpConnection { [OutputType('SnmpTools.ConnectionTest')] [CmdletBinding( DefaultParameterSetName = 'Community' )] param ( # General required parameters [Parameter( Mandatory, ValueFromPipeline, ValueFromPipelineByPropertyName )] [Alias('IPAddress')] [string]$ComputerName, [Parameter()] [ValidateRange(1, 65535)] [int]$Port = 161, [Parameter()] [string]$Oid = "1.3.6.1.2.1.1.1.0", #sysDescr [Parameter()] [ValidateRange(-1, 2147483647)] [int]$Timeout = 5000, [Parameter()] [switch]$Quiet, [Parameter(ParameterSetName = 'Community')] [Parameter(ParameterSetName = 'V3')] [SnmpVersion]$Version = [SnmpVersion]::V2C, # Parameter for SNMP version v1 and v2, both rely on a set community [Parameter(ParameterSetName = 'Community')] [string]$Community = 'public', # Parameters for SNMP version v3 [Parameter(Mandatory, ParameterSetName = 'V3')] [string]$Username, [Parameter(ParameterSetName = 'V3')] [ValidateSet( 'MD5', 'SHA1', 'SHA256', 'SHA384', 'SHA512' )] [string]$AuthenticationProtocol, [Parameter(ParameterSetName = 'V3')] [securestring]$AuthenticationPassword, [Parameter(ParameterSetName = 'V3')] [ValidateSet( 'DES', '3DES', 'AES', 'AES192', 'AES256' )] [string]$PrivacyProtocol, [Parameter(ParameterSetName = 'V3')] [securestring]$PrivacyPassword ) begin { Write-Verbose "Selected parameter set: $($PSCmdlet.ParameterSetName)" # Validate SNMP parameters Test-SnmpParameters ` -Version $Version ` -Community $Community ` -Username $Username ` -AuthenticationProtocol $AuthenticationProtocol ` -AuthenticationPassword $AuthenticationPassword ` -PrivacyProtocol $PrivacyProtocol ` -PrivacyPassword $PrivacyPassword } process { Write-Verbose "Processing $ComputerName" # Initialize variables and start the stopwatch for measuring response time $success = $false $reply = $null $errorMessage = $null $stopwatch = [System.Diagnostics.Stopwatch]::StartNew() # Attempt to get SNMP data try { $reply = Invoke-SnmpGet ` -ComputerName $ComputerName ` -Port $Port ` -Oid $Oid ` -Version $Version ` -Timeout $Timeout ` -Community $Community ` -Username $Username ` -AuthenticationProtocol $AuthenticationProtocol ` -AuthenticationPassword $AuthenticationPassword ` -PrivacyProtocol $PrivacyProtocol ` -PrivacyPassword $PrivacyPassword $success = $true } catch { # Failed to get SNMP data $errorMessage = $_.Exception.Message } finally { $stopwatch.Stop() } # If Quiet is specified, return only the success state, otherwise return a detailed object if ($Quiet) { $success } else { [SnmpConnectionTest]::new( $ComputerName, $Version, $success, $errorMessage, $stopwatch.ElapsedMilliseconds, $Oid, $(if ($reply) { $reply.Type } else { $null }), $(if ($reply) { $reply.Value } else { $null }) ) } } } |